,

RD-003-30/35【ASL / SG フロントナックル用 アルミ製 ナックルストッパー(2本入)】各¥520(税別)

  • このエントリーをはてなブックマークに追加

サスペンションの動きを妨げずに切れ角を調整!
アルミ製 ナックルストッパー  Φ3.0mm / Φ3.5mm の登場です!

発売当初よりご好評を頂いている【RD-001:ASL フロントナックル】と、【RD-001SG : SGフロントナックル】に最適な アルミ製 ナックルストッパーが登場します。
RWDドリフトカーは ナックルストッパー(ステアリングストッパー)にて最大切れ角を調整する方式が一般的ですが、切れ角を最大にする際、M3のセットスクリューを使用している方も多いのではないでしょうか。
M3セットスクリュー でも ストッパー の機能は果たしますが、表面がネジ形状の為、最大切れ角の際に サスペンションの動きを妨げてしまいます。

そんな際に活躍するのが この【アルミ製 ナックルストッパー】です!
M3セットスクリュー とは異なり 凹凸の無い表面になっていますので、最大切れ角の際でも サスペンションの動きを妨げることがありません。
更に 軽量なアルミ製となっていますので、鉄製のセットスクリューと交換することで軽量化にも効果を発揮します。

ラインナップは Φ3.0mm と Φ3.5mm の 2種類!
最大切れ角を実現する Φ3.0mm に加え、ほんの少しだけ切れ角を抑制したい時に便利な Φ3.5mm を準備しました。
市販されている Φ4.0mm では切れ角が足りない、Φ3.0mm では切れ角が多すぎるという時は Φ3.5mm が威力を発揮します!
現在 ストッパーとして M3セットスクリューを使用されている方、Φ4.0mmのストッパーよりも切れ角を増やしたいとお考えの方は是非お試し下さい。

<ラインナップ>
◆RD-003-30:ASL / SG フロントナックル用 アルミ製 ナックルストッパー (Φ3.0mm、2本入) ¥520(税別)
◆RD-003-35:ASL / SG フロントナックル用 アルミ製 ナックルストッパー (Φ3.5mm、2本入) ¥520(税別)

<主要寸法>
◆ネジ部: M3、長さ4.5mm
◆台座部直径: 5.5mm
◆台座底面から先端までの長さ: 16mm
◆六角穴寸法: 対辺 1.5mm
※RD-001:ASL フロントナックル に適した寸法となっています。
※他社製ナックルに使用する際は上記寸法をよくご確認の上ご購入下さい。

RD-003-30/35【Aluminum knuckle stopper for ASL / SG Front Knuckle (Φ3.0mm / Φ3.5mm, 2 pieces) ¥ 520 (excluding tax)

Adjust the angle of steering without interrupting the movement of the suspension!
Aluminum knuckle stopper Φ3.0mm / Φ3.5mm for RD-001 ASL Front Knuckle and RD-001SG SG Front Knuckle is now available!

RWD drift cars generally use a knuckle stopper (steering stopper) to adjust the maximum turning angle, but when maximizing the turning angle, many people use M3 set screws.
Even with the M3 set screw, the function of the stopper works, but the surface of the screw will hinder the movement of the suspension at the maximum turning angle.

This is where the [Aluminum Knuckle Stopper] comes into play!
Unlike the M3 set screw, the surface has no irregularities, so it does not hinder the movement of the suspension even at the maximum turning angle.
Furthermore, since it is made of lightweight aluminum, it is also effective in reducing weight by replacing it with an iron set screw.

The lineup consists of a Φ3.0mm and Φ3.5mm diameter part.
In addition to Φ3.0mm which realizes the maximum steering angle, Φ3.5mm which is an option when you want to control the steering angle only slightly is prepared.
Φ3.5mm is effective when the commercially available Φ4.0mm has insufficient steering angle and Φ3.0mm has too much angle!
If you are currently using an M3 set screw as a stopper or want to increase the steering angle more than a φ4.0mm stopper, please try it.

<Lineup>
◆ RD-003-30: Aluminum knuckle stopper for ASL / SG Front Knuckle (Φ3.0mm, 2 pieces) ¥ 520 (excluding tax)
◆ RD-003-35: Aluminum knuckle stopper for ASL / SG Front Knuckle (Φ3.5mm, 2 pieces) ¥ 520 (excluding tax)

<Main dimensions>
◆ Screw: M3, length 4.5mm
◆ Pedestal diameter: 5.5mm
◆ Length from base to tip: 16mm
◆ Hexagonal hole dimensions: 1.5mm across flats
* Above dimensions are suitable for RD-001 ASL Front Knuckle.
* If you use for the other knuckles, please check the dimensions of the knuckle, wheel before purchasing.

  • このエントリーをはてなブックマークに追加
ページ上部へ戻る